Celestron C100ED-R Instrukcja Obsługi Strona 9
- Strona / 67
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
9
4. Slide the R.A. slow motion knob onto the R.A. shaft.
The knob is a tension fit, so sliding it on holds it in place. As mentioned above, there are two R.A. shafts, one on
either side of the mount. It makes no difference which shaft you use since both work the same. Use whichever one
you find more convenient. If, after a few observing sessions, you find the R.A. slow motion knob is more accessible
from the other side, pull firmly to remove the knob, then install it on the opposite side.
5. The DEC slow motion knob attaches in the same manner as the R.A. knob. The shaft that the DEC slow motion
knob fits over is toward the top of the mount, just below the telescope mounting platform. Once again, you have two
shafts to choose from. Use the shaft that is pointing toward the ground. This makes it easy to reach while looking
through the telescope, something which is quite important when you are observing.
A
A
t
t
t
t
a
a
c
c
h
h
i
i
n
n
g
g
t
t
h
h
e
e
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
e
e
T
T
u
u
b
b
e
e
t
t
o
o
t
t
h
h
e
e
M
M
o
o
u
u
n
n
t
t
The telescope attaches to the mount via a dovetail slide bar mounting bracket which is mounted along the
bottom of the telescope tube. Before you attach the optical tube,
make sure that the declination and right ascension clutch knobs
are tight. This will ensure that the mount does not move suddenly
while attaching the telescope. To mount the telescope tube:
In order for the GT computerized mount to function properly,
before installing the optical tube, the mounting platform must be
positioned so that the Declination Index Marks are aligned (see Fig
2-8).
1 Locate the mounting bracket from the box containing the equatorial
mount head.
2 Attach the mounting bracket to the tube rings so that the tapered (narrow)
end is against the bottom of the tube rings.
3 Loosen the hand knob on the side of the CG-5
mount.
4 Slide the mounting bracket that is attached to
the bottom of the tube rings into the recess on the
top of the mounting platform (see figure 2-9).
5 Tighten the telescope mounting screw on the
CG-5 mount to hold the telescope in place.
6 Hand tighten the mounting platform safety
screw until the tip touches the side of the mounting
bracket.
NOTE: Never loosen any of the knobs on the
telescope tube or mount other than the R.A. and
DEC clutch knobs.
Advanced
GT Users!
Declination
Index Marks
Figure 2-8
Figure 2-9
- Warning 4
- Figure 2-6 8
- Figure 2-7 8
- Figure 2-5 8
- Figure 2-8 9
- Figure 2-9 9
- Installing the Finderscope 10
- Installing the Eyepieces 11
- Figure 2-15 14
- Helpful 20
- Tour Mode 21
- Constellation Tour 21
- Direction Buttons 21
- Rate Button 21
- Identify 23
- Scope Setup Features 24
- Observing 25
- Helpful 25
- UTILITIES 26
- ADVANCED GT 28
- Motion of the Stars 33
- Latitude 34
- Observing the Moon 37
- Lunar Observing Hints 37
- Observing the Planets 37
- Observing the Sun 37
- Terrestrial Photography 42
- Metering 42
- Reducing Vibration 42
- Auto Guiding 43
- CONNECTICUT 51
- 53
- Additional RS232 Commands 57
- CELESTRON TWO YEAR WARRANTY 66
Powiązane produkty i podręczniki dla Teleskopy Celestron C100ED-R
Teleskopy Celestron 21076 Instrukcja Obsługi
(20 strony)
(20 strony)
Teleskopy Celestron 52229 Instrukcja Użytkownika
(12 strony)
(12 strony)
Teleskopy Celestron 52229 Instrukcja Użytkownika
(10 strony)
(10 strony)
Teleskopy Celestron CG-4 Instrukcja Obsługi
(62 strony)
(62 strony)
Teleskopy Celestron 52238 Instrukcja Użytkownika
(10 strony)
(10 strony)
Teleskopy Celestron S-55F Instrukcja Obsługi
(45 strony)
(45 strony)
Teleskopy Celestron CG-4 Instrukcja Użytkownika
(64 strony)
(64 strony)
Teleskopy Celestron 14 Instrukcja Użytkownika
(11 strony)
(11 strony)
Victorinox Non manuels d'utilisation
La liste de Victorinox Non produits contient 10 manuels d'utilisation pour les modèles 10. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Komentarze do niniejszej Instrukcji